The Best Knife Sharpeners You Can Buy At KnifeCenter.com Media
Published: 5 years ago
Congrats to Joshua Hirsh on winning the Work Sharp Ken Onion Edition.
To get the best knife sharpener for you click this link: https://bit.ly/2ziZJDY
Whether you are running 440C or S90V, even the most super of steels will need to be sharpened eventually. This can be an intimidating task to some, but we’re going to take a look at three systems that make the job easy and achieve fantastic results. Let's check them out.
The first is the Spyderco Sharpmaker, an intuitive and easy to use device that can achieve hair-shaving results with ease on almost any steel out there, so long as the edge isn’t so far gone that you need to reprofile it.
All the elements come in this black plastic case that doubles as a stand, making this a very tidy package to store when not in use. There are two preset angles for the stones, meaning you don’t have to worry about maintaining the proper angle as you would when freehand sharpening on a flat stone. One way to check and see if the preset angle is matching up to your knife is to color the sharpened edge in with a black marker. After a few strokes, if the marks have disappeared, you know you are lined up properly.
Once the brass guards are in place, you start with the corner of the triangular brown medium stones. All you have to do is hold the blade straight up and down and place the heel of your blade at the top of the stone. Bring the blade straight down, and draw it towards you as you do, so that you hit the whole edge by the time you reach the bottom of the stone. Do this twenty times on each side of the blade, then rotate the stones and perform twenty strokes per side again, this time on the flat side. At this point, your blade should be able to cut paper, but we aren’t done yet.
Repeat the same steps as before, this time using the fine white stones, starting with the corner, and then the flat side of the triangle. Once you are finished, your edge should be hair popping sharp.
The stand also has a couple of other ways of holding the stones, allowing you to easily sharpen other tools such as chisels, scissors, and even straight razors. The Sharpmaker is a truly versatile device that is a classic for a reason - it just plain works.
Another system worth checking out that offers even more control over angle than the Sharpmaker is the Lansky Universal Knife Sharpening System. This set comes with a clamp that holds your blade steady and provides guide holes for the included stones so you can maintain the proper angle for your blade. Along with honing oil, the standard set comes with coarse, medium, and fine stones and is a great starting point. For a little extra money, higher-end sets come with more grits but they can also be purchased separately, as the standard set’s case comes with extra slots for storage if you choose to upgrade.
The process here is simple. Clamp the spine of your blade into place and attach the guide rods to the stones you wish to use. Starting with the coarsest stone you need, choose your angle and insert the guide rod into the proper hole. Sharpen as described earlier until you can raise a burr consistently on both sides and then move up to the next grit until your desired sharpness is achieved.
If you want to take your sharpening game to the next level, a powered unit from Work Sharp may be in order. Work Sharp has been raising the bar in the sharpening arena by thinking outside the box, and their Ken Onion Edition Knife & Tool Sharpener is one of our favorite units that they make, offering fast and accurate performance.
Unlike the previous units we showed you, the Ken Onion Work Sharp is driven by an electric motor, using abrasive belts and an adjustable angle guide to sharpen your edge.
After selecting your angle, set the heel of the blade on the belt, pull the trigger to start the motor, and pull the blade backward at a rate of one inch per second according to the manufacturer, stopping the motor before the tip of your knife passes the centerline of the belt. Then do the same for the opposite side. As with all the sharpening methods we’ve shown you, repeat these steps as necessary until the burr is consistent, then proceed to the next grit until desired sharpness is achieved.
To get the best knife sharpener for you click this link: https://bit.ly/2ziZJDY
Whether you are running 440C or S90V, even the most super of steels will need to be sharpened eventually. This can be an intimidating task to some, but we’re going to take a look at three systems that make the job easy and achieve fantastic results. Let's check them out.
The first is the Spyderco Sharpmaker, an intuitive and easy to use device that can achieve hair-shaving results with ease on almost any steel out there, so long as the edge isn’t so far gone that you need to reprofile it.
All the elements come in this black plastic case that doubles as a stand, making this a very tidy package to store when not in use. There are two preset angles for the stones, meaning you don’t have to worry about maintaining the proper angle as you would when freehand sharpening on a flat stone. One way to check and see if the preset angle is matching up to your knife is to color the sharpened edge in with a black marker. After a few strokes, if the marks have disappeared, you know you are lined up properly.
Once the brass guards are in place, you start with the corner of the triangular brown medium stones. All you have to do is hold the blade straight up and down and place the heel of your blade at the top of the stone. Bring the blade straight down, and draw it towards you as you do, so that you hit the whole edge by the time you reach the bottom of the stone. Do this twenty times on each side of the blade, then rotate the stones and perform twenty strokes per side again, this time on the flat side. At this point, your blade should be able to cut paper, but we aren’t done yet.
Repeat the same steps as before, this time using the fine white stones, starting with the corner, and then the flat side of the triangle. Once you are finished, your edge should be hair popping sharp.
The stand also has a couple of other ways of holding the stones, allowing you to easily sharpen other tools such as chisels, scissors, and even straight razors. The Sharpmaker is a truly versatile device that is a classic for a reason - it just plain works.
Another system worth checking out that offers even more control over angle than the Sharpmaker is the Lansky Universal Knife Sharpening System. This set comes with a clamp that holds your blade steady and provides guide holes for the included stones so you can maintain the proper angle for your blade. Along with honing oil, the standard set comes with coarse, medium, and fine stones and is a great starting point. For a little extra money, higher-end sets come with more grits but they can also be purchased separately, as the standard set’s case comes with extra slots for storage if you choose to upgrade.
The process here is simple. Clamp the spine of your blade into place and attach the guide rods to the stones you wish to use. Starting with the coarsest stone you need, choose your angle and insert the guide rod into the proper hole. Sharpen as described earlier until you can raise a burr consistently on both sides and then move up to the next grit until your desired sharpness is achieved.
If you want to take your sharpening game to the next level, a powered unit from Work Sharp may be in order. Work Sharp has been raising the bar in the sharpening arena by thinking outside the box, and their Ken Onion Edition Knife & Tool Sharpener is one of our favorite units that they make, offering fast and accurate performance.
Unlike the previous units we showed you, the Ken Onion Work Sharp is driven by an electric motor, using abrasive belts and an adjustable angle guide to sharpen your edge.
After selecting your angle, set the heel of the blade on the belt, pull the trigger to start the motor, and pull the blade backward at a rate of one inch per second according to the manufacturer, stopping the motor before the tip of your knife passes the centerline of the belt. Then do the same for the opposite side. As with all the sharpening methods we’ve shown you, repeat these steps as necessary until the burr is consistent, then proceed to the next grit until desired sharpness is achieved.